Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Fort Worth
Gate repair in Fort Worth runs $175-$650 for most hinge, post, and operator fixes, with full automatic gate motor replacements landing between $850 and $2,400 depending on the brand and the condition of your existing mounting. We dispatch from our Dallas-Fort Worth office straight to neighborhoods across Fort Worth, usually with a tech at your property within 90 minutes of your call. The thing that separates a lasting Fort Worth gate repair from a temporary one, though, is the soil under it. Blackland Prairie clay moves more than any contractor who hasn’t worked this ground expects. We’ve spent eleven years correcting what that movement does to gates. Call (817) 476-9945 and we’ll tell you what’s wrong, what it costs, and when we can be there.
Why Vance Gate Repair Fort Worth Is Fort Worth’s Preferred Gate Repair Company
Adrian Vance started this company in 2014 doing commercial access control, where everything gets documented because the building owner can’t watch the tech all day. That habit carried over to residential work. When we finish a gate repair in Fort Worth, you get a photo log of what was found, what was adjusted, and what part number went in. No other gate company we know of in Tarrant County hands you that record on a driveway gate repair.
Fort Worth homeowners call us because the price is written down before we touch a tool. That’s Clause 1 of our Haven Standard: have it in writing. You’ll see the flat price for the repair, the part, and the labor. If the repair isn’t right at any point in the next 365 days, we come back and make it right at no charge. That’s the 365-Day Done Right Promise, and it applies to every Fort Worth Gate Motor & Opener job we do.
A live person answers our phones 24/7. Not a voicemail tree. Not a callback request. When your gate won’t close and your 6-year-old tests the latch every ten minutes, you call and a human picks up. That matters as much in Fairmount as it does in Walsh Ranch.
Our Gate Repair Services in Fort Worth
Electric Gate Repair
Electric gate failures in Fort Worth fall into a few predictable buckets. The builder-grade operators in Alliance and Fossil Creek homes tend to burn out control boards after 5-7 years. The photo-eyes (those infrared beams that stop a gate when something crosses the path) get knocked out of alignment by post shift and then the gate just sits there, humming. We service all nine major automation brands including Viking, DoorKing, and Ghost Controls, so we handle Ghost Controls repair in Fort Worth and other brands on the motor that’s already on your property instead of selling you a replacement you don’t need. Most electric gate repairs in Fort Worth are done same-day.
Automatic Gate Repair
Automatic gates in Fort Worth fail in patterns that have everything to do with what they were bolted to at install. A slide gate in a Fort Worth neighborhood like Fossil Creek usually fails because the chain or belt wore out, or because a wheel bearing seized after spring rains washed silt into the track. A swing gate usually fails because the operator arm bent fighting a post that moved. We find the operator model, check the limit switches, verify the force settings, and hand you the written diagnosis before we start the fix. If a previous tech left wiring without conduit, we’ll tell you that too and price the correction separately.
Hinge & Post Repair
This is the repair western Fort Worth and the Alliance corridor call us for more than any other. The expansive clay under Tarrant County swells with spring rains and bakes hard in summer drought, and a gate post set in a 24-inch footing will heave out of plumb by March. A leaning post in western Tarrant County almost never means a bad install. It means the soil moved. In sandy soil markets, a tech can backfill with gravel and walk away. Here, the fix is excavating down 36-42 inches, setting a belled concrete footing, and repouring so the post has mass the clay can’t torque. We do this repair multiple times a week in Fort Worth.
Gate Realignment
If your gate scrapes the driveway or misses the latch, the post or the hinge moved. We adjust the hinges and the catch, resquare the frame, and check that the gate closes against the stops without dragging. On automatic gates, we re-check the limit switches after realigning because a gate that now travels ten inches differently can shear the arm if the limits aren’t reset. At a Walsh Ranch home last year, our tech found the hinge post had twisted in the clay after spring rains. We excavated to 40 inches, poured a belled footing, and converted the swinging gate to a slide so it stopped dragging across the brick pavers.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterTrusted Brands We Service in Fort Worth
We work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule operators. That means when you call about a Ghost Controls swing gate in Ryan Place or a DoorKing slide gate in Haltom City, we’re solving the problem on the existing motor, not quoting you a full-motor replacement out of convenience. We keep common control boards, gear kits, photo-eyes, and remote receivers stocked for Fort Worth service calls, and parts we don’t have on the truck typically arrive within one business day.
Common Gate Repair Problems We See in Fort Worth Homes
- Heaved posts after wet-dry cycles. The Blackland Prairie clay under much of Fort Worth expands after spring rain and contracts in summer heat. Posts set too shallow get pushed out of plumb, and the gate drags or stops latching. The repair requires a deeper footing, not just shims.
- Wires sheared inside the post when the clay shifted. Builder-grade swing operators in newer Fort Worth subdivisions were often wired without a dedicated conduit run. When the post torques, the low-voltage wire gets pinched and cut. The gate stops mid-cycle with no warning. We repair the wiring and rerun it through conduit so the next soil shift doesn’t repeat the failure.
- Manual gates converted without a loop detector. Alliance-area homebuyers who add automation to an ornamental pedestrian gate often skip the loop detector. The slide gate then fights traffic and strips the rack and pinion. We install the detector and replace the stripped gear.
- Ice storm damage to battery backups and control boards. The February 2021-style storms in Tarrant County hit operator batteries hard. A gate that worked fine in December fails in February because the backup battery died and the control board reset. We test the battery, replace it when needed, and reprogram the board.
Pricing for Gate Repair in Fort Worth, TX
| Service | Typical Price Range in Fort Worth |
|---|---|
| Hinge or latch adjustment | $175-$340 |
| Post reset with belled footing | $650-$1,400 |
| Photo-eye alignment or replacement | $150-$280 |
| Control board replacement | $350-$850 |
| Full swing-gate operator replacement | $900-$2,400 |
| Full slide-gate motor and rack replacement | $1,200-$2,800 |
The biggest cost factor in a Fort Worth gate repair is whether the post is the root cause. A simple hinge fix on a properly set post is a one-hour job. A post that needs excavation to 40 inches, a belled footing pour, and a day of cure time is the bigger number. You’ll see the exact price in writing before we start. The written quote is free, and if you have a written estimate from another local gate company, we’ll review it at no charge. It’s our free second opinion.
We Also Serve Cities Near Fort Worth
Beyond our Fort Worth work, we regularly handle Gate Repair jobs for homeowners in Haltom City, North Richland Hills, Hurst, and Kennedale. The soil conditions don’t change much at the Tarrant County line, and neither does the fix for a heaved post. If you’re in one of those cities, we can usually reach you just as fast as we reach Fort Worth proper.
For the full overview of our Gate Repair in Fort Worth services, that page covers every sub-service we offer in Tarrant County.
Serving Fort Worth, TX - Our Local Coverage Area
We’re based in the Fort Worth area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Fort Worth
The installer probably did exactly what a sandy-soil contractor would do: set the post in a 24-inch hole with gravel backfill. Fort Worth sits on Blackland Prairie clay that swells when spring rain soaks it. That swelling pushes a 24-inch footing sideways. Your post didn’t fail because the install was wrong by Texas-sand standards. It failed because the footing wasn’t built for this clay. The correct repair is excavating to 36-42 inches and pouring a belled concrete footer that the soil can’t torque. Call (817) 476-9945 and we’ll assess your post depth and give you a written price to reset it.
Yes, and most Walsh Ranch gates convert cleanly. The key is the power and conduit run. If the builder left conduit stubbed near the gate, the conversion is straightforward: operator, receiver, safety edges, and a loop detector if it’s a slide. If the builder didn’t leave conduit, we trench and run a dedicated circuit, then install. Either way, you’ll see the written price before we start, and we leave a photo log of the operator model, wiring runs, and final settings.
Thirty-six to forty-two inches, with a belled bottom. That’s the depth below the zone where Blackland clay expands and contracts. Anything shallower will move within a year or two, and the gate will start missing the catch or dragging. We pour belled footings on every post reset in Fort Worth, and we photograph the excavation before the pour so you can see the depth.
The battery backup or the control board usually fails after an ice storm in Fort Worth. The cold saps the battery’s ability to hold charge, and the board can reset and lose its travel limits when power flickers. We test the battery under load, replace it if it’s weak, reprogram the board, and photograph the limit-switch readings. You’ll know exactly what failed, not just that it’s fixed.
The cost difference comes from the soil. A hinge replacement is a hinge replacement in either city. But Fort Worth’s Blackland clay means a gate that won’t latch is frequently a post that has moved, and that’s an excavation, a footer pour, and a cure day, not a $30 hinge swap. In Dallas, where soil conditions vary more by neighborhood and many areas drain differently, a simple hinge replacement is more often the whole story. The written price you get from us includes whatever the actual cause is, not just the surface symptom. Call (817) 476-9945 for an exact quote on your gate; estimates are free and include the post-depth check.
What to Fix Before the Next Rain
Here’s the honest Fort Worth scheduling advice: if your gate worked in June and starts dragging in March, check the post before the next spring rain. A gate that’s out of plumb by an inch now will be out by two after the next soaking. Every repair we do in Fort Worth starts with measuring post plumb and checking the footer depth, because on this soil, the post is the foundation of the gate, not the hardware bolted to it. If your gate has heave movement, a gate that worked in June will lean by March. The fix before the rain is cheaper than the fix after it. Call (817) 476-9945 and we’ll schedule a tech to check your gate posts, your operator, and your hinges, and hand you a written price for whatever needs doing. No pressure, no urgency theater, just a documented price and a real diagnosis.
Written by Fort Worth gate repair specialist Adrian Vance, Owner at Vance Gate Repair, serving Fort Worth and Tarrant County with documented gate repair since 2014.