Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Arlington, TX
Gate access control in Arlington usually means retrofitting a keypad, card reader, or phone-entry system onto an automated gate that was installed 15 to 25 years ago, back when the HOA ran everything through a single call box. The Blackland Prairie clay under most of the city has shifted those gate posts out of plumb in the years since, and a control system that worked fine at 2 degrees of rotation often fails at 4. We service the electronics, re-plumb the post if needed, and leave you a written record of every setting. Call (817) 476-9945 for a free estimate.
Why Arlington Homes Are Different
Arlington sits on highly expansive clay that shrinks into deep cracks during summer droughts and heaves back up with spring rains. That wet-dry cycle tilts gate posts, warps frames, and binds automated operators year after year. The city’s huge wave of HOA master-planned subdivisions built from the 1980s through the early 2000s means thousands of ornamental iron and tubular steel driveway gates are now reaching their major-repair window all at once. Along the Highway 360 and Sublett Road corridors, we routinely find automated slide gates from the late 1990s with posts rotated 3 to 5 degrees out of plumb purely from clay movement. The operator arm binds, the motor burns out, and the real repair is re-plumbing the post before the new operator will run true. HOA architectural committees also govern what materials can be swapped in, so repairs often mean matching existing wrought-iron or powder-coated steel rather than replacing with whatever is cheapest.
Our Main Arlington Services
Most Arlington homeowners call us about one of three things: a gate that stopped moving, a gate that needs to be replaced, or a motor that quit. Here is how each one typically goes.
Gate Repair in Arlington
Gate repair in Arlington frequently follows the same pattern: the gate worked for years, then one season it started scraping, then the operator began straining, then it stopped. What we find is almost always a post that has drifted out of plumb from clay movement, a hinge that has wallowed out, or a rack that no longer lines up with the drive gear. We fix the underlying alignment problem, not just the symptom, and we photograph every adjustment. Gate Repair in Arlington covers the full scope of what we do.
Gate Installation in Arlington
New gate installation in Arlington means digging footings deep enough to get below the active clay zone, or the same heaving cycle will undo the work within a few seasons. HOA rules usually dictate the style, finish, and even the hinge hardware, so we pull the architectural guidelines before we quote. The written price covers the gate, the posts, the operator if you want one, and the documentation. Gate Installation in Arlington walks through the process.
Gate Motor & Opener in Arlington
Operator failure in Arlington is rarely just a burned-out motor. The clay shifts the post, the arm binds, and the motor works against resistance until it overheats. We service nine automation brands, so we can repair what is already on the property rather than pushing a replacement. Gate Motor & Opener in Arlington has the full breakdown.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Arlington
Arlington’s older HOA communities, built largely between the 1980s and early 2000s, are full of access-control systems that have outlived their original wiring and keypads. The clay heave that tilts posts also pulls underground conduit apart and breaks the low-voltage wiring that connects keypads, card readers, and safety loops. Gate Access Control is the service hub if you want the full picture. The fix here is rarely just swapping the keypad face: we trace the damaged run, repair the conduit, and reset every limit and photo-eye before we leave, with a photo log of the whole job.
Keypad Entry
Signs you need it
The keypad lights up but the gate does not respond, or some codes work while others stopped working.
What it costs in Arlington
Replacing a damaged keypad face or the entire pedestal keypad body runs $350 to $900, while a full standalone keypad entry system including wiring and programming lands between $850 and $2,000.
How we do it
We trace the wiring back to the operator board, replace or rewire the keypad, bench-test every code, and photograph the final programmed state.
Phone Entry
Signs you need it
The call box rings but callers cannot be heard, or the buzzer function works only intermittently, which on an Arlington HOA entry gate is usually a corroded junction in the underground conduit.
What it costs in Arlington
Phone entry systems connected through a phone line run $850 to $2,000 installed, and if we need to replace the conduit segment before installing, the line-item total is the same figure plus the trenching labor we quote in writing first.
How we do it
We locate the dead or corroded segment, pull new low-voltage wiring, mount the call station, and run the relay wiring back to the operator with a connection diagram left on file.
What Gate Access Control Costs in Arlington
| Item | Typical range in Arlington |
|---|---|
| Keypad entry replacement | $350 - $900 |
| Full keypad entry system | $850 - $2,000 |
| Phone entry system | $850 - $2,000 |
Can you add a keypad to an existing Arlington gate?
Yes. Most operators from Ghost Controls, DoorKing, and Elite accept a wired or wireless keypad input, and we can usually complete the retrofit in a single visit. If the existing wire was damaged by clay movement, we run a new low-voltage line. Call (817) 476-9945 for a written price.
Does a phone entry system work with a cell phone only?
It depends on the panel, but many current systems program a cell number directly and call it when a visitor presses the button. We configure the unit to ring the homeowner’s mobile line, no landline required, and test it on site.
Gate Parts & Welding in Arlington
Arlington’s ornamental iron and tubular steel gates, common throughout the city’s HOA subdivisions, fail most often where metal meets post. The clay movement that tilts posts also cracks the welds on hollow tube frames during hard freezes, and the resulting sag scrapes the driveway. Gate Parts & Welding covers the full parts and fabrication side. We replace the hinge, gusset the crack, and re-hang the gate so the operator is not fighting the frame.
Hinge Replacement
Signs you need it
The gate drops when it opens, drags on the ground, or the hinge pin has wallowed the post hole into an oval.
What it costs in Arlington
A standard hinge replacement runs $250 to $700.
How we do it
We cut the old hinge off, weld a new bracket or sleeve over the worn post steel, and re-hang the gate with the new hinge greased and photographed.
Welding and Frame Repair
Signs you need it
You can see a crack at a corner joint, the gate rack is pulling away from the frame, or it rattles with a hollow sound when it moves.
What it costs in Arlington
Welding and frame repair runs $200 to $700.
How we do it
We grind the crack to clean steel, weld the joint, add a gusset where the frame needs reinforcement, and photograph the weld before and after paint.
What Gate Parts & Welding Costs in Arlington
| Item | Typical range in Arlington |
|---|---|
| Hinge replacement | $250 - $700 |
| Welding and frame repair | $200 - $700 |
| Steel part fabrication and replacement | $150 - $700 |
Can you weld an Arlington gate without removing it?
Often yes, especially for crack repair and gusset work where we can work in place. If the post itself is rotated 4 or 5 degrees from clay movement, we pull the gate, re-plumb the post, and weld it back square. Call (817) 476-9945 and we will tell you which one your gate needs.
Do you replace just one hinge or the whole set?
We replace what is worn, but on Arlington gates where one hinge has wallowed out, the other hinge has usually taken the same load and we recommend doing the pair. The written price shows each line item, so you see exactly what you are paying for.
Brands We Service in Arlington
We stock common parts for DoorKing, Elite, Ghost Controls, and Mighty Mule operators on our Arlington service trucks, which means most keypad, limit-switch, and photo-eye jobs are done same-visit. Our brands page lists the full nine we service.
Pricing for Gate Repair in Arlington, TX
| Service | Typical range in Arlington |
|---|---|
| Keypad entry replacement | $350 - $900 |
| Full keypad entry system | $850 - $2,000 |
| Phone entry system | $850 - $2,000 |
| Hinge replacement | $250 - $700 |
| Welding and frame repair | $200 - $700 |
| Steel part fabrication and replacement | $150 - $700 |
In Arlington specifically, the two big price drivers are post condition and HOA material requirements. If your post has rotated 3 to 5 degrees from clay movement, the repair quote includes re-plumbing before any new part goes on, and if the HOA requires a specific iron finish or powder coat, that is a separate line item. Every price is written and handed to you before work starts, under Haven Standard Clause 1.
Neighborhoods We Serve in Arlington
We work the full Arlington area from Dalworthington Gardens through the HOA subdivisions along Sublett Road and the Highway 360 corridor. Response time for most Arlington neighborhoods is same-day when you call before 2 p.m.
- Dalworthington Gardens
- Southwest Arlington
- North Arlington
- Pantego
- Interlochen
Service Area - Cities Near Arlington
Our Arlington crews also cover the neighboring communities where the same clay-soil and HOA patterns show up. That includes Kennedale, TX, Burleson, TX, Grand Prairie, TX, and Fort Worth, TX. Dispatch is coordinated from our Dallas-Fort Worth office, but the technicians are local to the Arlington area.
Serving Arlington, TX - Our Local Coverage Area
We’re based in the Arlington area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Arlington
Most Arlington calls are scheduled same-day when they come in before 2 p.m., and a live person answers the phone 24/7. Emergency gate-down jobs get priority, and the written price is delivered before any work begins on site.
For like-for-like hardware and finish repairs, usually not. But if you are replacing a visible gate, the HOA’s architectural guidelines typically require approval first. We can pull the relevant standards for you before we quote, so the price reflects the right materials.
Yes, and it is the single most common cause of operator failure we see in Arlington. The expansive clay tilts posts out of plumb, the arm binds, and the motor works against resistance until it burns out. We re-plumb the post before installing any new operator, which is why our Arlington repairs hold up.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Arlington Customers Say
"Quoted in writing, installed on the day promised, and the price did not move. The crew was licensed and the number was on the paperwork."
- Wes A."Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R."Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B.