Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Benbrook, TX
Gate access control work in Benbrook usually comes down to one of two problems: a keypad or intercom that stopped reading, or an operator that opens for everyone except the person at the driveway. The homes here lean heavily toward acreage lots and properties backing up to Lake Benbrook and Corps of Engineers land, which means we see far more automatic driveway gates than the denser suburbs west of Fort Worth. If your gate opens for a code but not your phone, or the keypad works but won’t close the gate, call (817) 476-9945 and we’ll name the fix before we touch anything.
Why Benbrook Homes Are Different
Benbrook’s housing stock runs from 1960s ranch-style homes on generous lots to semi-rural estates along the Lake Benbrook corridor with ornamental iron and steel pipe driveway gates. That matters because the gate hardware on those older properties often predates modern automatic operator standards, and a repair call frequently turns into a parts-and-realignment job rather than a simple motor swap.
The bigger variable is the dirt. Fort Worth Prairie clay under most of Benbrook shrinks hard during summer drought and heaves when the rains return, shifting gate posts enough to shear hinge welds and throw swing-gate operators out of alignment. Technicians near the Lake Benbrook shoreline see a recurring failure we call “floating post”: clay swell tilts a post just enough to trigger the obstruction-detection stop, the gate freezes open, and the homeowner is convinced the motor died when the actual fix is re-plumbing the post and resetting travel limits. North Texas hail adds a spring spike in calls for dented and warped aluminum panels.
Our Main Benbrook Services
The two calls we get most from Benbrook homeowners are access control problems on existing gates and parts or welding work on gates that are structurally sound but mechanically worn. These three pages cover the other major jobs.
Gate Repair in Benbrook
A gate that won’t open, won’t close, or grinds halfway through its travel usually has a specific mechanical cause: a broken hinge, a dead capacitor, a limit switch set past travel, or a post that moved in the clay. On properties along the lake where 1970s and 1980s hardware is still in service, the repair often involves matching older parts or fabricating a bracket rather than bolting on a generic replacement. Gate Repair in Benbrook covers the full diagnosis and fix process, from the first phone call to the photo log you get at the end.
Gate Installation in Benbrook
New gate work in Benbrook runs heavily toward steel and iron driveway gates sized for larger lots, often with operators added at the same time. Installation here means accounting for clay soil movement, so we set posts deeper than the frost line and brace against the same swell-and-shrink cycle that wrecks older gates. Gate Installation in Benbrook walks through materials, sizing, operator pairing, and what a full written scope looks like before any digging starts.
Gate Motor & Opener in Benbrook
When the operator is the problem rather than the gate itself, the job is diagnosing whether it’s the motor, the control board, the limit switch, or the power supply. We service nine automation brands directly, so a Viking on a lake property or a Ghost Controls on a 1980s pipe-rail gate gets repaired rather than replaced when the part is honestly available. Gate Motor & Opener in Benbrook details the sub-jobs, the common failure points, and what a same-day motor swap should cost.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Benbrook
Access control on a Benbrook gate means the difference between a gate that holds the line where private property meets public Corps land and a gate that opens for anyone who tries it. Most systems we see here are keypad- or remote-based on the older estates, with phone entry and video intercom becoming more common as homeowners replace 1980s-era hardware. Our Gate Access Control work always includes a written record of every setting and wiring change, so a future service call never starts from zero.
Keypad Entry
Signs you need it
The keypad takes multiple button presses, code works only sometimes, or the housing is cracked and letting rain into the circuit board.
What it costs in Benbrook
Keypad replacement runs $185-$450 installed, depending on whether it’s a basic wired unit or a wireless model with rolling-code security.
How we do it
We verify the wiring path first, then mount the new keypad, set the master code, and photograph the final programming screen for the job record.
Phone Entry
Signs you need it
Callers get no dial tone at the gate, the system rings but won’t release the operator, or the unit won’t store new numbers.
What it costs in Benbrook
Phone entry systems run $850-$2,750 depending on whether it’s a cellular or landline unit and how many numbers need programming.
How we do it
We test the phone line or cellular signal at the column, match the new unit to your operator’s relay, program the directory, and test every stored number before we leave.
What Gate Access Control Costs in Benbrook
| Item | Typical range in Benbrook |
|---|---|
| Keypad replacement | $185-$450 |
| Phone entry system | $850-$2,750 |
| Video intercom | $450-$1,600 |
Can you integrate my existing gate operator with a new phone entry system?
Yes, in most cases. The relay wiring on LiftMaster, Viking, Ghost Controls, and DoorKing operators all follow the same dry-contact logic, so a new phone unit connects without replacing the operator. The exception is very old hardware with no accessory terminal block.
Do I need a separate power run for a video intercom at the gate?
Not always. Many wired video intercoms run on a two-wire PoE connection, which means we can often pull a single cable from the house rather than trenching a separate electrical line. We verify available conduit before quoting anything.
Gate Parts & Welding in Benbrook
Benbrook’s older gates fail at the joints before the motor fails. Hinges shear, posts tilt in swelling clay, and steel pipe rails crack at the welds that have held for thirty or forty years of Texas weather. Our Gate Parts & Welding service fixes the physical gate, not just the operator bolted to it, and every job leaves with a written parts record and photos of the finished work.
Hinge Replacement
Signs you need it
The gate drags on the latch side, the hinge pin is visibly worn or bent, or the gate squeals even after greasing every pivot point.
What it costs in Benbrook
Hinge replacement runs $140-$450 per hinge depending on the gate’s weight and whether the post side needs a weld-on repair plate.
How we do it
We support the gate on a jack stand, cut or unbolt the old hinge, weld or bolt the new one in place, and photograph the finished assembly with an angle finder on the post.
Post Replacement
Signs you need it
The post leans more than a few degrees, the base shows rust-through, or the gate operator trips its obstruction stop every few cycles no matter how many times limits are reset.
What it costs in Benbrook
Post replacement runs $350-$950 per post depending on depth, concrete work, and whether the existing post is steel or wood set in active clay.
How we do it
We cut the post at grade, remove the old footing, set a new post below frost line with concrete, and re-hang the gate before re-plumbing the operator’s travel limits.
What Gate Parts & Welding Costs in Benbrook
| Item | Typical range in Benbrook |
|---|---|
| Hinge replacement | $140-$450 per hinge |
| Post replacement | $350-$950 per post |
| Custom welding repair | $95-$350 per section |
Can you weld a cracked steel gate on site, or does it need to go to a shop?
Most cracks can be welded on site. We bring a mobile welder to the property, grind the crack clean, weld both sides, and re-paint the repair area. Only severely warped or rusted sections need shop work, and we’ll tell you before you pay anything.
How long does a post replacement take on a Benbrook lot with clay soil?
One to two days including concrete cure time. The actual digging and setting takes a few hours; we schedule the operator re-alignment for after the concrete has set so travel limits are reset once, correctly, on a stable post.
Brands We Service in Benbrook
We work on Viking, Ghost Controls, DoorKing, and Elite operators regularly in Benbrook, along with five other major automation brands. Common control boards and photo-eyes for these brands stock locally or arrive within a day. Our brands page lists every manufacturer we service and the parts we keep on the truck.
Pricing for Gate Repair in Benbrook, TX
| Service | Typical range in Benbrook |
|---|---|
| Keypad replacement | $185-$450 |
| Phone entry system | $850-$2,750 |
| Video intercom | $450-$1,600 |
| Hinge replacement | $140-$450 per hinge |
| Post replacement | $350-$950 per post |
| Custom welding repair | $95-$350 per section |
| Gate operator motor replacement | $450-$1,200 |
| Control board replacement | $250-$650 |
| Photo-eye replacement | $120-$280 |
| Track and roller repair | $200-$700 |
Prices push toward the top of these ranges on Benbrook properties where clay movement has compounded the original failure: a shifted post plus a stripped hinge plus a burned-out limit switch costs more than any one of those alone. Every job gets a written flat price before work starts, so the number you approve is the number you pay.
Neighborhoods We Serve in Benbrook
We cover all of Benbrook, including the acreage lots and lake-adjacent estates where most gate work happens. Response times for gate repair calls across the city are typically same-day when the job is urgent, with scheduling flexibility for planned installations and larger welding work.
- Lake Benbrook shoreline properties
- Timber Creek
- Whisperwood
- Pecan Valley
- Benbrook Lakeside
Service Area - Cities Near Benbrook
Our Benbrook crews also cover the surrounding Tarrant County area, including Fort Worth, TX, Haltom City, TX, Saginaw, TX, and White Settlement, TX. Dispatch is coordinated from our Dallas-Fort Worth office, with technicians on the road in Benbrook every day.
Serving Benbrook, TX - Our Local Coverage Area
We’re based in the Benbrook area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Benbrook
For a gate stuck open or closed, we dispatch same-day in nearly all Benbrook neighborhoods, including lake-adjacent properties. Repair calls carry no dispatch premium for urgency. A live person answers the phone 24/7 at (817) 476-9945.
Most gate replacements on existing posts don’t require a permit. New installations with posts set in concrete may need a basic zoning or setback check, and some lake-adjacent or Corps-adjacent properties have additional easement rules. We verify before quoting.
Clay movement is a continuing condition, not a one-time failure. The fix that lasts is deeper post setting, better drainage at the post base, and an operator with properly set obstruction sensitivity so minor seasonal movement doesn’t trigger repeated safety stops. We document all of it on every visit.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Benbrook Customers Say
"Quoted in writing, installed on the day promised, and the price did not move. The crew was licensed and the number was on the paperwork."
- Wes A."Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R."Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B.