Linear Gate Installation Nationwide

Linear Gate Installation in Fort Worth: What to Know First

Linear gate installation in Fort Worth typically runs between $850 and $2,400 for a complete swing or slide gate setup, depending on motor size, gate weight, and whether the post footings are already poured. We’re an independent Linear service provider, not a factory dealer, which means we install and repair the Linear equipment you bring or already own without steering you toward a replacement you don’t need. Most Linear installations we handle are done within one to two days on site, with the written price in your hand before the first tool comes off the truck.

Call (817) 476-9945

This page is for Fort Worth homeowners who own a Linear opener, bought a Linear gate kit, or inherited Linear equipment with a new house and want someone who actually knows the brand’s quirks. If you’ve already read the three-star reviews on other gate companies and want to see a real dollar figure before you commit, you’re in the right place. Call (817) 476-9945 and a live person answers, any hour.

How Linear Products Fail - and How We Fix Them

Linear builds solid, workhorse gate operators, but every brand has its repeating failure points. Here’s what we actually see on Linear equipment in Fort Worth driveways:

• Linear ACT-31B / ACT-34B arm brackets seizing after weather exposure. The articulated arm on these swing-gate models uses a steel pivot bolt that corrodes over three or four North Texas seasons. When it binds, the gate starts and stops in jerks or trips the obstruction sensor. We replace the bolt with a sealed-grease assembly and set the arm geometry fresh. Most shops replace the whole arm. That’s a few hundred dollars the owner didn’t need to spend.
• Linear LRA linear actuator limit switches drifting out of travel. On the LRA series, the limit cams ride against mechanical stops inside the actuator tube. Fort Worth’s temperature swings cause the cam nuts to back off slowly, and the gate over-travels or slams the stop. We reset the limits, photograph the new cam positions, and note the part number in the job record so next time it’s a five-minute check, not a diagnosis from scratch.
• Linear M3S slide-gate chain tension slack causing phantom reverse triggers. The chain on a slide-gate operator stretches after the first year of operation, especially on heavy ornamental gates. Too much slack lets the chain whiplash the sprocket, which the M3S control board reads as an obstruction. The gate reverses halfway and won’t hold position. We run the chain to spec, set the tensioner to the measured gate weight, and record the reading.
• Linear APeX photo-eye misalignment from post settling. Fort Worth’s clay soil expands and contracts enough to move a gate post a quarter inch over a wet-dry cycle. That quarter inch throws the photo-eye beam off and the gate refuses to close. The eye wasn’t bad. The post moved. We check beam alignment with a meter before touching the opener, then shim or re-seat the sensor. On new installs, we set photo-eyes on standoff mounts that tolerate more post movement.
• Linear control boards losing memory after power sag. The older M-series and some early APeX boards don’t brownout-protect their internal memory. A sagging transformer or a hard lightning-season brownout in a Fort Worth summer can wipe limit settings and force-reverse sensitivity. We install a surge-rated disconnect on every Linear job we touch and set the board parameters back to OEM spec, then log the dipswitch positions in your photo record.

Our Linear Gate Installation Process

Here’s how a Linear gate installation runs with us, from the first call to the last photo:

1. 1
   The call and the honest conversation. You tell us what Linear model you have or want installed, what the gate weighs if you know it, and what’s already on the property. We tell you right then whether a site visit is required or if we can quote a range over the phone. No “call for a quote” games. The number is the point.
2. 2
   Written scope and price. Before any work starts, you have a written flat price in hand. That’s Haven Standard Clause 1. The price covers what we agreed to install, and it does not change mid-job unless you ask for scope changes in writing.
3. 3
   Parts decision: OEM vs. quality aftermarket. For Linear actuators and arms we use Linear OEM parts where they’re load-bearing or safety-critical. For items like photo-eyes, keypads, and edge sensors, we may offer a quality aftermarket equivalent that matches specs and saves real money. We tell you which is which and why, and it’s in writing.
4. 4
   Installation, set, and document. We mount the operator, secure the gate travel stops, set the force sensitivity to the actual gate weight, and align every sensor. Then we photograph what we found, what we set, and what we installed. You get that photo log before we leave.
5. 5
   Test cycle and written record. We run the gate through full open-close cycles with the safety edges and photo-eyes live. We record limit positions, force settings, and the part number of every component installed.
6. 6
   The 365-Day Done Right Promise. If any part of the installation is not right within one full year, we make it right at no additional charge. No argument, no fee, no fine print.

Before

After

What Linear Gate Installation Costs in Fort Worth

Most Linear gate installations in Fort Worth fall into these ranges, including labor and standard hardware. The exact number depends on gate weight, power availability at the post, and whether new footings are needed:

• Single swing gate, Linear ACT-31B or similar, new install on existing posts: $850-$1,350
• Double swing gate, twin Linear actuators with master-slave controls: $1,800-$2,400
• Sliding gate, Linear M3S or equivalent chain-drive operator: $1,300-$1,900
• Pedestrian gate, Linear light-duty swing operator: $700-$1,100
• Control board replacement on any Linear model, parts and labor: $250-$480
• Full re-install of an existing Linear opener onto a new gate: $450-$800

What moves the price: gate weight (a 600-pound wrought-iron double gate needs more operator than a 200-pound tube steel single), whether a dedicated 120V circuit is already at the post, and whether the existing posts are plumb and set below the frost line. If the gate posts are moving, any operator we mount on them is a waste of your money. We’ll tell you that plainly.

Every Linear installation quote covers labor, hardware, fasteners, and the documented photo record. The price is agreed in writing before we start. Call (817) 476-9945 for an exact quote on your specific gate. Estimates are free.

Why Fort Worth Homeowners Call Vance Gate Repair Fort Worth for Linear Work

We treat residential Linear gates the same way Adrian Vance treated commercial access-control sites starting in 2014: name what you found, name what it costs, name what you left behind. That habit carries into every driveway gate we touch in Fort Worth.

We service nine major gate-automation brands, including LiftMaster, Mighty Mule, Ghost Controls, and DoorKing alongside Linear. If your property has a Linear opener on the driveway and a Ghost Controls unit on the pedestrian gate, one technician handles both without pretending one brand is junk to sell you another. Every visit leaves a photographed record of what was set, what was replaced, and what the gate should do next. And the 365-Day Done Right Promise covers every completed installation for a full year. A live person answers the phone at (817) 476-9945 24 hours a day. No voicemail loop, no call-back queue.

FAQs