Linear Gate Access Control Nationwide

Linear Gate Access Control in Fort Worth: What to Know First

Linear gate access control repair in Fort Worth typically runs between $185 and $520, with most keypad and receiver issues resolved in a single visit. We’re an independent Linear service provider, meaning we work on your existing equipment without steering you toward a replacement unless the numbers genuinely don’t make sense. If your Linear keypad stopped opening the gate, your remote stopped pairing, or your phone entry system clicks but won’t release, this page tells you what’s happening and what it costs to fix. Call (817) 476-9945 and a live person answers, day or night.

Call (817) 476-9945

How Linear Products Fail - and How We Fix Them

Linear made gate access control gear for decades, and a lot of it is still running on Fort Worth driveways. The failure modes are consistent enough that we can usually name the problem from a phone description. Here’s what we see most often.

• Linear MegaCode receivers losing programmed remotes. The MegaCode platform (used across APeX, Delta-3, and older Multi-Code gear) stores remote codes in non-volatile memory, but we regularly find receivers on Fort Worth gates that have dropped every programmed remote after a power flicker. The fix is usually a re-flash of the receiver, not a new board. We photograph the dip switch positions and the programming sequence before and after so there’s a record.
• Linear AM-KP keypads with corroded terminal strips. The AM-KP and older AK-11 keypads use small screw terminals that sit inside an enclosure that isn’t always sealed well against North Texas humidity. We see green corrosion on terminals, intermittent digit entry, and codes that work sometimes. Cleaning the terminals and re-sealing the enclosure fixes most of them. If the membrane pad itself is worn through, that’s a part replacement, and we’ll show you the old one.
• Linear photo-eye pairs that trip falsely in afternoon sun. The MBS-series photo-eyes Linear used on many gate operators are sensitive to direct low-angle sunlight. Fort Worth’s west-facing gates get hit hard between about 5 and 7 p.m. in summer. We test by shading the receiver with a piece of cardboard before calling the sensor dead. Misaligned eyes get realigned and photographed; sun-blinded eyes get a shade hood, which costs far less than a new safety device.
• Linear G Series and GateMaster operators with a dead access-control relay. The relay that fires when a keypad or card reader sends the open command is a known weak point on older Linear G Series and GateMaster boards. The operator runs fine, the remote opens the gate, but the keypad does nothing. We bench-test the relay, and if it’s confirmed dead, we often replace just the relay rather than the whole board. That’s a $60 to $140 fix instead of a $400+ board.
• Linear LRA-series receivers that won’t learn a new remote. The LRA-series and EXA-series receivers have a learn button sequence that’s easy to get wrong if you haven’t done it a hundred times. We’ve had customers say they tried for an hour and gave up. The usual cause is holding the learn button too long and erasing all remotes by accident. We reprogram, document the new remote ID, and show you the exact sequence before we leave.

Our Linear Gate Access Control Process

1. 1
   You call, you talk to a person. We ask what the keypad, remote, or phone entry unit is doing, and what it stopped doing. We may ask for the model number off the receiver or keypad face.
2. 2
   We dispatch with the right parts on the truck. Our techs carry Linear MegaCode remotes, AM-KP keypads, MBS photo-eyes, relay substitutes, and common Linear receiver boards. Eighty percent of our Linear calls are resolved in one trip.
3. 3
   Diagnostics come first, and they’re documented. We test voltage at the receiver, check the photo-eye alignment, and confirm whether the board, the relay, the keypad, or the wiring is actually at fault. No guessing.
4. 4
   We write the price before we touch a tool. You get a flat number in writing, parts and labor, before any repair starts. That’s Haven Standard Clause 1 in practice.
5. 5
   We do the repair, then test everything. Keypad codes enter correctly. Remotes learn and open the gate. Safety devices stop the gate when they should.
6. 6
   You get the photo log and the part numbers. Before we leave, you have a written record of what was found, what was replaced, and what the gate should do next. The 365-Day Done Right Promise covers the work for a full year.

Before

After

What Linear Gate Access Control Costs in Fort Worth

Most Linear access control repairs in Fort Worth land between $185 and $520. Replacing a failed keypad runs $210 to $340 with a Linear AM-KP or equivalent. Programming a replacement MegaCode receiver is $185 to $285. Swapping a dead access-control relay on an older G Series board runs $60 to $140. A new photo-eye pair with alignment and shade-hood install, when needed, lands between $240 and $390. The price moves based on how far the gate sits from the house, whether we’re trenching, and whether OEM versus quality aftermarket parts are selected. You’ll get the exact number in writing before any work starts, and our estimates are free. Call (817) 476-9945 and we’ll set a time.

Why Fort Worth Homeowners Call Vance Gate Repair Fort Worth for Linear Work

We take the same commercial documentation habit onto every residential driveway. Adrian Vance started in access-control work in 2014, running wiring diagrams and panel labels on commercial sites before he ever touched a residential gate. That habit never left. Every Linear job we do in Fort Worth leaves a photo log of the old part, the new part, and the settings we left behind. We service eight other gate-automation brands too, LiftMaster, Mighty Mule, Ghost Controls, and DoorKing included, so if your Linear system shares a gate with another brand’s motor, one visit covers it. The 365-Day Done Right Promise means if the repair isn’t right, we make it right, no charge, no argument. Name what you found. Name what it costs. Name what you left behind.

FAQs