Ghost Controls Gate Parts & Welding Nationwide

Ghost Controls Gate Parts & Welding in Fort Worth: What to Know First

We repair Ghost Controls gate openers and weld the hardware around them across Fort Worth, and most parts-and-welding jobs are quoted in writing and completed within one to three business days once the parts are in hand. A hinge replacement on a Ghost Controls swing gate typically runs $340-$680 depending on gate weight and post condition; a welded bracket repair runs $180-$320. Call (817) 476-9945 and we’ll give you a written price before any work starts.

Call (817) 476-9945

If you own a Ghost Controls system in Fort Worth and the gate sags, drags, won’t latch, or the opener strains against a misaligned hinge, this page tells you what’s actually failing and what it costs to set it right. We are an independent Ghost Controls service provider, not a factory-authorized dealer, which means we fix what’s broken rather than steering you toward whatever’s easiest to replace.

Key Takeaways:

• We carry or source Ghost Controls-specific parts: hinges, brackets, gate rollers, latches, and weld-in reinforcement plates.
• Written price before work starts, photo record when we leave. That’s the standard on every job.
• One-year Done Right Promise covers every repair and weld we perform.

How Ghost Controls Products Fail - and How We Fix Them

Ghost Controls builds reliable residential openers, but the metal around them takes the abuse. In Fort Worth, we see the same failure patterns repeat across neighborhoods like Wedgwood, Ridglea Hills, and out toward Benbrook. Here’s what breaks and what we do about it.

• Sagging hinge posts on TSS1 and R Series swing gates. The opener arm pushes, the post leans, and the gate starts dragging on the latch side. The motor isn’t the problem; the post has shifted. We excavate, reset the post in fresh concrete, weld reinforcement plate to the hinge side if the metal’s thin, and re-align the opener arm to the gate’s new travel arc. Done wrong, the post leans again in six months. Done right, it stays put for years.
• Cracked weld at the opener arm bracket on heavy wrought-iron gates. Fort Worth’s heavy ornamental gates put constant stress on the bracket where the Ghost Controls arm bolts to the gate frame. The factory bracket is fine for light gates; on 400-pound iron, the weld at the base cracks. We grind out the old weld, re-weld the bracket with proper penetration, and add a gusset plate so the load spreads across more steel. This is the most common welding repair we do on Ghost Controls systems.
• Worn gate rollers on sliding gate kits. The Ghost Controls slide gate kits use rollers that pick up grit and wear unevenly. Symptom: the gate moves fine for six feet, then shudders and slows. Owners assume it’s the motor. It’s usually a flat-spotted roller. We replace rollers and check the track for wear, and if the track’s grooved, we weld in a new section rather than hanging a whole new track. Parts cost stays under $200 typically.
• Stripped hinge threads on thin-gauge gate frames. This turns up on tubular steel gates where the factory hinge bolts were drilled and tapped into thin stock. The bolts work loose, the gate droops, the Ghost Controls opener fights the change in geometry. We drill out the stripped holes, weld in threaded bungs, and re-hang the gate so the hinges hold torque without chewing through the metal again.
• Broken latch or magnetic lock bracket after wind storm. Fort Worth gets real wind, and a gate that catches a gust with the opener disengaged will slam. The latch striker plate or maglock bracket bends or snaps. We fabricate and weld a replacement bracket on-site in most cases, then re-align the striker so the Ghost Controls auto-close cycle doesn’t pinch or bind.

One pattern we see on Ghost Controls jobs that other brands don’t produce as often: the opener’s battery backup masks the underlying mechanical problem for months. The gate moves slower than it should, the opener compensates, and nobody notices the hinge has been ovaled out until the motor overheats. By the time we’re called, the repair is two-part: mechanical first, then re-dialing the opener’s travel and force settings. Adrian Vance has pulled more than one limit-switch cover off a Ghost Controls board and found the travel set six or seven degrees past where the gate actually stops, because the previous owner’s gate was already sagging when the opener was installed.

Our Ghost Controls Gate Parts & Welding Process

1. 1
   Call comes in, we ask what the gate is doing. We ask for the model number if it’s readable. TSS1, R Series, and the slide kits all have different failure profiles. A live person answers, 24/7.
2. 2
   We inspect on-site and name what we found. We measure the gap, check the post with a level, photograph the hinge wear and the weld condition, and write down the model and serial. You see the diagnosis, not a shrug.
3. 3
   Parts decision: OEM, quality aftermarket, or fabricated. For Ghost Controls boards and enclosed components, we use factory parts when the repair touches the opener itself. For steel work, brackets, hinges, rollers, and reinforcement plates, we source from local steel suppliers and weld shops we’ve used for years. You get the part number and the price in writing before the torch lights.
4. 4
   The repair or weld. We cut, grind, weld, re-set, and re-hang the gate so it moves true. Then we re-attach the Ghost Controls arm, re-set the travel limits, and set the force so the opener isn’t fighting the gate.
5. 5
   Test cycles. We run the gate through 15 to 20 open-close cycles in both directions, check the auto-close, check the photo-eye alignment, and photograph everything.
6. 6
   You get the record. Photo log of what was found, what was set, what was installed. Written record of part numbers, torque specs, and limit settings. Filed with our job record and left with you.

Before

After

What Ghost Controls Gate Parts & Welding Costs in Fort Worth

Every job is priced in writing before we start. These are the ranges we see most often on Ghost Controls work around Fort Worth.

Quotes are free. The price you sign off on is the price you pay. No surprise line items, no “we had to do extra work” invoice at the end. That’s Haven Standard Clause 1, and it applies on every Ghost Controls job we run in Fort Worth.

Why Fort Worth Homeowners Call Vance Gate Repair Fort Worth for Ghost Controls Work

We’re not the only gate company in Fort Worth. But we’re the one that hands you a written price, shows you the photos of what we found, and stands behind the work for 365 days. That’s not marketing. That’s the Done Right Promise, and it’s been on every job since Adrian Vance started this company in 2014 out of commercial access-control work.

We service Ghost Controls alongside eight other automation brands, LiftMaster, Mighty Mule, DoorKing, and the rest. What that means for you: we’re not going to tell you to rip out a working Ghost Controls opener and replace it with whatever we have on the truck. We fix the opener you’ve got, and we weld the hardware around it so it keeps working. When your Ghost Controls system needs something we can’t repair, we’ll tell you that flat and show you the evidence. Then we’ll price the replacement in writing.

Fort Worth gates take heat, wind, and heavy ornamental iron. The technicians we dispatch are background-checked and uniformed, and you’ll have the name and photo of the person coming to your house before they arrive. No guessing who’s in the driveway.

FAQs