Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Hinge & Roller Replacement: The Fort Worth Owner’s Guide
FAAC hinge and roller replacement in Fort Worth typically runs $220-$480 installed, depending on whether it’s a single hinge swap or a full roller set on a slide gate. We carry OEM FAAC hinges and rollers for most common residential models, plus durable aftermarket options that match or exceed factory specs. Most replacements are done same day when we arrive, because we keep the common sizes on the truck.
Owners usually discover a hinge or roller problem the same way: the gate starts dragging, groaning, or catching mid-travel, and eventually the motor strains or the gate stops seating against the stop. It’s rarely a sudden failure. It’s a steady sag that gets worse in the Texas heat, and by the time the gate stops moving, that hinge has been working overtime for months.
Key Takeaways
- Installed cost runs $220-$480 in Fort Worth, part and labor included
- We stock OEM and aftermarket FAAC hinges and rollers on the truck
- Same-day replacement available on most FAAC models
- Written price before the first tool comes out, per Haven Standard Clause 1
- 365-Day Done Right Promise covers every hinge and roller replacement
Which FAAC Models This Applies To
FAAC puts its name on a lot of swing and slide gate hardware, but hinge and roller replacement is most common on swing-arm systems like the FAAC 402, 412, 415, and later S418 and E145 lines. Slide gate rollers show up on FAAC 740 and 741 slide kits, as well as aftermarket slide assemblies paired with FAAC motors. The compatibility gotcha: FAAC changed hinge pin diameters between some older 400-series kits and the newer S-series, and a 412 hinge will not seat properly on an S418 bracket without slop. We check the pin diameter and the bracket bolt pattern before ordering anything.
Identifying what’s actually on your gate takes five minutes. The hinge or roller body will have a casting number, and the bracket spacing is easy to measure. No FAAC hinge we’ve replaced has been unlabeled, so if you’re looking at a blank, unbranded hinge, it’s likely an aftermarket mount. That’s not a problem; aftermarket can be perfectly good, but the pin diameter still has to match. We stock OEM for FAAC’s common residential lines and a machined aftermarket line we trust for older, discontinued hardware.
BeforeAfterSigns Your FAAC Hinge & Roller Replacement Is Failing
- The gate sags at the free end. A worn hinge lets the gate leaf drop, usually a quarter to a half inch at first. The motor works harder to move the same gate, and the limit switch has to struggle to find its end point.
- You hear a grinding or popping noise during travel. A roller with flat-spotted bearings or a seized wheel drags instead of rolling. In Fort Worth’s dry summers, the factory grease inside the roller can dry out and turn to paste.
- The gate catches or sticks at one point in the arc. Hinge play lets the gate shift, and the bottom edge clips the concrete or a low spot. You’ll usually see a scrape mark if you look.
- The opener struggles and the clutch kicks in early. FAAC motors have internal force limiting; when the hinge or roller friction rises, the motor thinks it’s hit an obstruction. The gate may stop mid-cycle and reverse.
- Visible rust on the hinge pin or roller axle. Surface rust isn’t fatal, but rust around the pin, especially with heat spalling on the roller surface, means the part is nearing the end. North Texas doesn’t get salt like coastal areas, but our freeze-thaw cycles and summer kiln heat age metal hardware faster than most owners expect.
Replacement Cost & What’s Included
In Fort Worth, you’re looking at $220-$320 for a single hinge replacement, hardware included, and $350-$480 for a full roller or multi-hinge job. The spread comes from a few things: OEM FAAC parts run a little higher than aftermarket, and gates with one failing hinge usually have another one close behind, so we quote per hinge and let you decide how many to do. Heavier wrought-iron gates, like the ones out in Westover Hills with long cantilevers and custom leaf weights, sit at the higher end because the hinge has to carry more.
Every price is written and handed to you before work begins. That’s Haven Standard Clause 1. You get the part number, the labor line item, and the warranty term in writing, and the price doesn’t move after you approve it. The work itself is covered by our 365-Day Done Right Promise. If the hinge or roller fails within a year, we fix it at no charge.
DIY or Call Us?
A swing gate hinge or slide roller is load-bearing equipment, and the tension in a gate leaf can release fast when the last bolt comes out. We don’t recommend removing a hinge on a heavy gate without blocking and support, and a slide gate with worn rollers can shift during the swap if it’s not chocked. If you want to check something yourself, look for visible slop in the hinge by lifting the gate leaf (carefully, with a pry bar, just a quarter inch) and watch for movement around the pin. You’ll feel the play immediately if the hinge is shot.
Where owners get into trouble is replacing a single hinge on a older gate and leaving the other one half-worn; the new hinge takes all the wear in under a year. The practical fix is matching the gate’s hardware in sets, and that’s easier with a part number in hand and the old hinge off the gate. Call us at (817) 476-9945 if you want the written quote before committing. No surprise invoice, no handshake math.
FAQs
Most FAAC residential hinges and rollers last six to nine years in the Fort Worth climate, but that’s a real range; a shaded gate in Arlington Heights will outlast a full-sun gate in Walsh Ranch by two or three years. The heat kills grease and accelerates corrosion, so we see faster wear on unshaded, south-facing gates. Call (817) 476-9945 if you’re getting less than five years out of a set, because something else is usually wrong with the gate’s geometry or balance.
If the play is in the pin and the hinge body is intact, we can sometimes re-bush and re-pin a heavy FAAC hinge and save the casting. Rollers are a different story; once the bearing is flat-spotted or the wheel surface is spalled, the only honest fix is a new roller. We’ll quote the repair option if it’s structurally sound. Call (817) 476-9945 and we’ll tell you which side of the line your part is on.
A single hinge swap on a typical FAAC swing gate takes about an hour on site, and a full roller set on a slide gate usually takes two hours including re-leveling the gate. Most replacements in Fort Worth are done the same day we arrive. Call (817) 476-9945 to schedule.
We stock the common FAAC hinge pin diameters and roller assemblies for 402/412/415 and S-series swing systems, plus matching aftermarket hardware for discontinued models. We also keep parts for LiftMaster, Mighty Mule, and Ghost Controls on board. If your hinge is an uncommon size, we order it and return within a couple of days. Call (817) 476-9945 with your gate’s model or a photo of the hinge, and we’ll confirm what fits before we roll out.
Get Your FAAC Hinge or Roller Replaced in Fort Worth
If the gate is sagging, grinding, or shutting down mid-travel, call Vance Gate Repair Fort Worth at (817) 476-9945. We’ll give you a written price before work starts, match the right FAAC part (or a proper aftermarket equivalent), and leave you a photo log of what we found, what we set, and what we installed. Name what you found. Name what it costs. Name what you left behind.
Written by Adrian Vance, Owner, Vance Gate Repair Fort Worth at Vance Gate Repair Fort Worth, serving Fort Worth and nearby areas.