Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterWhy Fort Worth Homeowners Choose Ghost Controls Gate Repair
We provide independent Ghost Controls service in Fort Worth, and we’re one of the few local shops that genuinely knows the TSS1, DTP1, and AXDP operator families inside and out. Fort Worth’s expansive clay soil torques hinge posts out of alignment every wet-dry cycle, and our lightning-prone spring storm season fries control boards faster than any mechanical wear ever could. That means our Ghost Controls work here is as much about soil conditions and surge protection as it is about the operator itself. We’re not authorized by Ghost Controls, and we’ll say that plainly, but we repair their equipment every day with written pricing before we touch a single wire. Call (817) 476-9945 for an estimate on your Ghost Controls opener.
Why Trust Vance Gate Repair Fort Worth for Your Ghost Controls Gate Repair?
Adrian Vance started this company out of commercial access-control work in 2014, and he brought a habit with him: write down what was found, what was replaced, and what the gate should do next. That’s the standard our Ghost Controls technicians still follow. When we open a TSS1 solar operator and find the sunlight sensor caked with dust, we photograph it. When we pull an AXDP board and see reversed-polarity burn marks from a jump-start, we note the exact terminal damage in writing. You get that photo log before we leave, not just a verbal summary.
We’ve serviced Ghost Controls operators in Fort Worth long enough to know which failures repeat on which series. TSS1 units lose charging capacity when the panel gets shaded or dirty. DTP1 arms bind when clay-soil shift pulls the hinge posts out of line. AXDP boards cook when a dead battery gets jump-started backward. Knowing the failure pattern means we diagnose faster and quote accurately. We stock OEM Ghost Controls control boards, arm assemblies, and remotes locally, and we have trusted aftermarket options for older chassis where a board rebuild no longer makes financial sense. Under the Haven Standard, your written price is in your hand before work begins, and the 365-Day Done Right Promise covers everything we complete.
Common Ghost Controls Gate Repair Problems We Fix in Fort Worth
- AXDP control board failure after a reversed-polarity jump-start. This is the most common AXDP board death we see in Fort Worth. A homeowner jump-starts a dead battery, clips the cables backward for half a second, and the board’s diode bridge fries. The symptom is a dead operator with a burned smell at the control board. We replace the OEM board, correct the battery connections, and document the old board’s damage with photos.
- TSS1 solar panel losing charge from dust, sap, or partial shading. The TSS1’s sunlight sensor sits near the top of the panel. When dust, tree sap, or a new fence shadow blocks it, the panel stops sending charge to the battery, and the operator drains down within a few cycles. We clean the sensor, reposition the panel if needed, and test the charge voltage under load before calling it fixed.
- DTP1 actuator arm binding after clay-soil hinge shift. Fort Worth sits on Blackland Prairie clay. It heaves and shrinks with every rain and drought cycle, pulling gate posts out of plumb by inches. A DTP1 arm that was tramming smoothly at install now binds because the hinges moved. We reset posts, re-shim the hinge plates, and realign the actuator so the arm travels without resistance. This is the dominant Ghost Controls repair call in western Tarrant County.
- FP1 remote range dropping below 20 feet from antenna degradation or radio interference. The FP1’s receiver antenna is a thin wire inside the control housing. Over time, corrosion or a nearby LED transformer’s RF noise cuts usable range down to a car-length or less. We test range with fresh batteries, check the antenna connection, replace the antenna if it’s pitted, and relocate the receiver away from known noise sources.
- TSS1 and DTP1 operators failing after lightning storms. Spring storm season in Fort Worth brings direct and nearby strikes that travel through fence wiring and into the operator. The surge protector, if present, sacrifices itself. If absent, the board’s logic chip takes the hit. We replace boards, install UL-listed surge suppressors at the junction box, and reprogram remotes when the memory chip gets wiped.
BeforeAfterGhost Controls Parts & Our Repair-vs-Replace Approach
For Ghost Controls operators under five years old, we install OEM parts: control boards, arm assemblies, limit switches, and remotes. The part numbers match exactly, and the failure symptoms map one-to-one with what you were experiencing. For TSS1 and AXDP units older than five years, we’ll give you an honest comparison. A quality aftermarket arm kit from DKS or HySecurity often runs about half the cost of a new Ghost Controls arm, and on a 10-year-old chassis, that aftermarket component frequently outlasts the remaining factory parts around it. We’ll show you both prices in writing and let you choose. No pressure toward replacement when repair will hold.
We stock common Ghost Controls parts in our Fort Worth service vehicles: OEM control boards for TSS1 and AXDP series, arm assemblies, remote fobs, limit switches, and solar panel components. If we need to order something, we’ll tell you the lead time before we leave. Call (817) 476-9945 if you want a straight answer on parts availability for your model.
Our Ghost Controls Service Process - Step by Step
- 1
Diagnosis. We test the operator under power, check battery voltage and solar input where applicable, verify limit-switch position, and inspect the hinge posts for clay-soil movement. We photograph what we find, including switch readings and any visible board damage.
- 2
Written quote. Before any work starts, you get a flat price on paper for the repair or replacement. That’s Haven Standard Clause 1. The price doesn’t change after we open the housing.
- 3
Repair or install. We replace the failed component, update the firmware if the board supports it, and set limit switches precisely. For Ghost Controls operators, we also check that the solar panel angle matches the season if your unit runs on solar.
- 4
System test. The gate gets a full cycle test under load: open, close, obstruction reversal, remote range, and auto-close timing if active. Every setting is logged.
- 5
Documentation and warranty. You receive a photo log of what was found, what was adjusted, and what was installed. Every completed Ghost Controls repair carries the 365-Day Done Right Promise. If it’s not right within a year, we make it right at no charge.
Ghost Controls Products We Service & Install in Fort Worth
Our Ghost Controls in Haltom City and Fort Worth coverage spans the brand’s current and recent operator families: the TSS1 heavy-duty solar swing gate opener, the DTP1 dual swing gate opener, the AXDP dual swing gate opener, and the FP1 premium single swing gate opener. We also service solar battery backup systems paired with these operators and handle gate realignment when clay-soil movement has thrown posts and hinges out of line. Remote control programming and replacement are standard parts of every Ghost Controls visit we make.
We Also Service These Brands
Ghost Controls is one of nine gate-automation brands our Fort Worth technicians service. If your property has a mix of operators across different gates, we can handle LiftMaster, Mighty Mule, and DoorKing units as well. No need to coordinate two separate companies for a property with mixed-brand gates.
FAQs - Ghost Controls Gate Repair Service in Fort Worth
No. We are an independent Ghost Controls service provider, not an authorized dealer or warranty station. That independence means we recommend the repair that makes sense for your gate, not the part that satisfies a manufacturer relationship.
We install OEM Ghost Controls control boards, arm assemblies, and remotes when the operator is under five years old or exact symptom matching matters. For older TSS1 and AXDP units, we often recommend quality aftermarket arms from DKS or HySecurity at roughly half the cost of a new Ghost Controls arm. You’ll see both options priced in writing before you decide.
Most Gate Repair jobs for Ghost Controls board replacements and arm alignments in Fort Worth are completed the same visit, typically one to three hours depending on the failure. Solar panel issues that require repositioning or battery replacement may add an hour. Post-reset work for clay-soil hinge shift is its own appointment since the concrete needs cure time.
We service the TSS1 solar swing opener, DTP1 dual swing opener, AXDP dual swing opener, and FP1 single swing opener. The common failures vary by series: TSS1 panels lose charge, AXDP boards die from reversed jump-starts, DTP1 arms bind from post shift, and FP1 remotes lose range from antenna wear.
If your Ghost Controls operator is still under factory warranty, manufacturer-authorized service may be required to preserve that coverage. Our independent repairs won’t affect the non-warranty components, but we’ll tell you upfront if a repair could impact an active claim and suggest contacting Ghost Controls directly if that’s the better path.
Ghost Controls Gate Repair in Saginaw, TX and Fort Worth control board replacement typically runs $340 to $620 depending on the series and whether surge protection is added. Arm assembly replacement runs $280 to $520. Remote programming and replacement runs $45 to $120 per remote. Solar panel component replacement runs $180 to $380. Post-reset work from clay-soil movement is quoted per job after we see the footing depth and post condition. Call (817) 476-9945 for a written estimate on your specific model. Estimates are free.
Book Your Ghost Controls Service in Fort Worth, TX
Our Fort Worth Ghost Controls technicians carry the diagnosis tools, OEM and aftermarket parts, and documentation equipment in the truck. A live person answers the phone 24/7 at (817) 476-9945. We’ll schedule your Ghost Controls service, write the price before work starts, and leave you with the photo log and part numbers that prove what was done.
Written by Adrian Vance, Owner at Vance Gate Repair Fort Worth, serving the Fort Worth area since 2014.