Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Access Control for Fort Worth Homeowners
Gate access control in Fort Worth means giving people a way in without handing them a key, and taking that way back the moment they shouldn’t have it anymore. A working keypad, phone-entry system, or card reader on a driveway gate is the difference between a gate that protects the property and a gate that’s just a heavy decoration. Vance Gate Repair Fort Worth has installed and serviced access control on residential and light-commercial gates across Tarrant County since 2014, with 22,000+ gates repaired or installed in that time. Every job leaves with a written price agreed before work starts and a photo record of exactly what was found, what was set, and what was installed. Call (817) 476-9945 and a live person answers, any hour.
What Our Gate Access Control Service Includes
Access control isn’t one product. It’s the layer of hardware and wiring that decides who gets through, when they get through, and whether the gate opens at all. Below is what we actually service on Fort Worth properties, and what the work looks like when we’re standing in front of the gate.
Keypad Entry
A keypad mounted on a pedestal or gooseneck post lets anyone with the right code open the gate. We see the most trouble in Fort Worth with weather-exposed keypads: rain gets past the membrane, the contacts corrode, and codes start working intermittently before they stop working at all. Vance Gate Repair Fort Worth replaces worn keypads, runs new low-voltage wiring where the old line has been chewed through by landscape equipment, and sets the entry and exit codes in front of you before we leave. You get a written record of the new code programming so you’re not locked out of your own system two months from now.
Remote Control
A handheld transmitter or visor remote sends a rolling-code signal to a receiver wired into the gate operator. When remotes stop working one at a time, it’s usually the battery or a dropped transmitter. When they stop working all at once, it’s usually the receiver or a blown fuse on the control board. We test the receiver with a known-good remote, check the antenna placement, and where the receiver is the problem we replace it rather than selling you a whole new operator. Most remote-control trouble in Fort Worth is a $15 part or a 20-minute reprogram, not a motor replacement.
Phone Entry
Phone entry systems let a delivery driver or visitor call a number from the keypad and get buzzed in by a homeowner who may be on the other side of Fort Worth or the other side of the country. The system ties into the gate operator’s control board and typically runs on a cellular or VoIP connection. We install and service phone-entry modules, program the tenant or caller list, and test the open-command relay with a live call before we leave. Weak cellular signal at the gate location is the most common failure point we diagnose in Fort Worth’s hillier and tree-covered lots.
Card Reader
A card reader mounted near the gate reads a proximity card or fob and sends the open signal when the credential matches. It’s common on small HOA gates and private lanes inside the city, and it’s one of the most forgiving systems to maintain, provided the reader stays dry and the wiring connections stay tight. Vance Gate Repair Fort Worth installs and replaces card readers, enrolls or clears user credentials, and works with existing HOA systems where the board wants minimal disruption. If the reader powers up but won’t read, we trace the Wiegand wiring back to the controller and repair the line rather than replacing everything on a hunch.
Video Intercom
A video intercom adds a camera and two-way audio at the gate, so the homeowner can see who’s asking to come in before pressing the open button. We install and service video intercom systems that tie into a phone app, a wall-mounted monitor, or both. Camera placement matters more than most people expect: the lens has to see a face at vehicle height without staring into the afternoon sun, and that means testing at the actual install hour, not just bolting the bracket where it looks right. Our installs include the photo log of the finished placement and the wiring path.
Smart Access
Smart access means the gate talks to a phone, a hub, or a home-automation platform. Homeowners open and close the gate from an app, get alerts when the gate operates, and sometimes create one-time codes for guests or service people. We integrate gate operators with app-based controllers, set up user permissions, and where the property has spotty Wi-Fi at the gate, we install a cellular bridge or an external antenna rather than letting the system limp along on a weak signal. Smart access is useful, but it depends on clean low-voltage wiring and a stable operator underneath it, and we document both before we hand it over.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Access Control
We work on DoorKing access control hardware regularly in Fort Worth. DoorKing’s telephone-entry and card-reader systems are common on small gated lanes and private communities, and we’ve done enough of them that we stock common DoorKing replacement parts on the truck: keypad membranes, relay boards, and the weather seals that keep the enclosure dry. When a DoorKing system fails, our first move is to test the power supply and the relay trigger separately, because the board is rarely the first thing that died.
Ghost Controls and Mighty Mule show up more on residential driveway systems, and we service both. Ghost Controls openers with the app-based module are popular in Fort Worth’s newer subdivisions, and we handle the pairing, the range issues, and the sensor alignment that come with them. Mighty Mule systems are widely sold as DIY kits, which means we see a fair number of them after the original install didn’t quite work: gate travel set wrong, the safety sensor bypassed, the arm bracket loose. We repair and reprogram both brands, and we’ll tell you honestly whether the system is worth repairing or whether the money is better spent on replacement. We don’t steer toward replacement when the repair is the better path.
Elite gate operators land somewhere between residential and light commercial, and we service those as well. Whatever the brand, if the gate has a motor on it and a keypad next to it, we can work on it. The nine automation brands we service most in Fort Worth are LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, but the diagnostic process is the same regardless of the label: test power, test the trigger, test the safety circuit, and document every setting before changing anything.
BeforeAfterSigns You Need Gate Access Control Right Now
- The keypad works for some people and not others. Codes that work intermittently usually mean the keypad membrane is wearing out or a solder joint behind the keypad is failing from weather exposure. Ignoring it tends to end with a keypad that stops working entirely during a rain week, which is exactly when you need it.
- The gate opens when no one pressed anything. A gate that ghost-opens usually points to a relay failing on the control board, a wiring short, or a receiver picking up stray signal from a neighbor’s system. It’s not just annoying; it’s a nightly security hole on the property.
- You hear a click but the gate doesn’t move. The click means the control board heard the signal, but the operator isn’t getting the power or the motor has a problem. The fix can be as small as a capacitor or as large as a motor, and the only way to know before spending money is to test it in order.
- The intercom rings but you can’t hear anyone, or they can’t hear you. Audio that drops one direction usually means a failed mic or speaker wiring, but it can also mean a power-supply problem at the gate station. Until it’s fixed, the gate might as well not have an intercom on it.
- You’re still using a physical key or manually opening the gate at night. A manual gate bypasses the entire security point of having a gate. If the access system has been down for weeks and everyone’s gotten used to opening it by hand, the property is unprotected and the operator is likely developing wear from repeated manual operation.
Our Gate Access Control Process - Step by Step
- 1
Diagnostic visit and written scope. We arrive, run the system, and document what’s happening: readings at the control board, state of the low-voltage wiring, condition of the keypad or reader, and the travel limits on the operator. Before any tool comes out, you receive a written scope and a flat price. That’s Haven Standard Clause 1: have it in writing. Since 2014, Adrian Vance has run every job this way.
- 2
Power and trigger testing. We check incoming power to the operator, then test the open command from each access device: keypad, remote, phone module, card reader, whichever is present. This isolates whether the problem is the access device, the wiring, or the operator itself. The testing order matters, and we document the readings at each step.
- 3
The repair or install. We make the repair with OEM or equivalent parts, run new wiring where the existing line is compromised, and set everything to manufacturer spec. When we replace a component, we photograph the old part, the new part, and the finished installation. The part number goes on the written record.
- 4
System test with you present. We test every opening device in front of you, exit and entry, and watch the gate run a full open-close cycle. We also test the safety features: the photo-eye, the reversing edge, whatever’s on the gate. If it doesn’t pass, we don’t leave it that way. The 365-Day Done Right Promise covers all completed work for one full year.
- 5
Documented photo record. Before we leave, you get a photo log of what was found, what was set, and what was installed, plus a written summary of the work. No future technician has to guess what was done, and you never have to pay twice to rediscover the same problem. That’s the documentation habit Adrian Vance built on commercial access-control sites starting in 2014, and it applies to every residential gate in Fort Worth.
How Much Does Gate Access Control Cost in Fort Worth?
A keypad replacement on a Fort Worth driveway gate typically runs $180 to $450, depending on the keypad model and whether the mounting pedestal or wiring needs attention. Adding a phone-entry module usually runs $450 to $900, and a full video intercom system with app access typically lands between $900 and $1,800 installed. If the issue is a failed receiver or relay board rather than the access device itself, most repairs fall between $120 and $350. If the whole operator needs to be replaced because the motor is burned out, a typical swing-gate motor replacement runs $800 to $2,400 depending on the brand and whether the arm bracket is intact. Those are honest Fort Worth market numbers: real, documentable, and explained in writing before any work starts.
What changes the price: the condition of the existing low-voltage wiring, the distance from the gate to the house or power source, whether the old equipment is still supported by the manufacturer, and whether the gate itself is square and balanced. A gate that’s dragging on the hinges will burn out motors and make every access device work harder, and we’ll tell you that during the diagnostic rather than letting you find out after the second motor fails. The free estimate includes the diagnostic findings, the written price, and the photo documentation. We also offer a free second opinion on any written estimate from another gate company: bring the paperwork to us and we’ll review it at no cost, with no obligation to book the work. Talk to our Fort Worth gate team for a written quote.
Gate Access Control Near Fort Worth - Our Service Area
We service gate access control across Fort Worth and the surrounding Tarrant County communities, including Haltom City, Saginaw, White Settlement, Richland Hills, Watauga, Forest Hill, North Richland Hills, Benbrook, Hurst, Kennedale, and Keller. A live person answers the phone 24/7, and same-day dispatch is often available for access-control failures on occupied properties. See more about our work in Gate Access Control in Haltom City and Gate Access Control in Saginaw. For gate-related repairs beyond access control, see our gate repair, gate motor and opener, and gate parts and welding services.
Serving Fort Worth, TX - Our Local Coverage Area
We’re based in the Fort Worth area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Access Control in Fort Worth
Gate access control is the system that lets authorized people open a gate without a physical key, using a keypad code, remote, phone call, card, or app. It includes the access device at the gate, the wiring that connects it to the gate operator, and the operator’s trigger input. A properly installed access system means you can add and remove users without changing the locks on the property. Call (817) 476-9945 for a free estimate on installing or repairing yours.
Most access-control installations in Fort Worth take one workday, assuming the gate operator itself is in good shape and the wiring run is straightforward. More complex jobs, like long wire runs under concrete or video intercom systems with multiple monitors, can take a day and a half to two days. We’ll give you a written scope and timeline before any work starts, and we stand by it. Estimates are free.
Keypad replacements run $180 to $450, phone-entry modules $450 to $900, and video intercom systems $900 to $1,800 installed. Repairs to receivers, relays, and wiring typically fall between $120 and $350. The exact price depends on what’s at the gate, what’s failed, and how much wiring work the job needs. Call (817) 476-9945 for an exact quote; the estimate is free and the price is written before any work begins.
Yes, we service DoorKing, Ghost Controls, Mighty Mule, Elite, and every other brand mentioned on this page. We stock common DoorKing replacement parts and have deep experience with Ghost Controls app-based systems in Fort Worth. If you have a different brand, call us anyway: the diagnostic process doesn’t change, and we don’t steer toward replacement when repair makes sense. Estimates are free.
In most cases yes, for occupied properties in Fort Worth and the surrounding area. A failed access system on a property you need to secure is a legitimate emergency, and a live person answers our phone 24/7 to take your call at (817) 476-9945. We’ll give you a straight answer about whether we can get there today, and the written price is the same regardless of the hour.
All completed gate access control work carries the 365-Day Done Right Promise: if the repair isn’t right within one year, Vance Gate Repair makes it right at no additional charge, no argument. The promise covers parts and labor on the work we performed. We also document every job with photos and written records, so warranty claims don’t turn into a debate about what was done. Call (817) 476-9945 with any questions about coverage.
Clear any overgrowth or debris from around the gate, keypad, and operator housing, and make a note of which devices are misbehaving and when it started. If you have remotes or gate codes, gather them so we can test every method of opening during the diagnostic. You don’t need to do anything technical; the diagnostic itself is part of the free estimate. We’ll walk the property with you, test everything in order, and hand you a written price before any work begins.
Schedule Your Gate Access Control Service in Fort Worth Today
Your gate should open for the people you trust and stay shut for everyone else. If the access control isn’t doing that, the problem isn’t going to fix itself, and every week it’s down is a week the gate is a liability rather than a line of defense. Call Vance Gate Repair Fort Worth at (817) 476-9945 for a free estimate, a written price before any work starts, and a documented record of everything we do. A live person answers, any hour, every day.
Written by Adrian Vance, Owner at Vance Gate Repair, serving Fort Worth since 2014.